Официальные release notesDJI getallfile API · 2023-12-14
What’s New?
• Added support for Zenmuse X9-8K gimbal camera, which supports 4K resolution and up to 120fps full frame video recording. Due to performance limitations, clean footage is not supported in ProRes RAW format and 48 project frame rate or above video and only supports the OSD output when using the HDMI port of the main body and SDI port of the expansion plate with Zenmuse X9-8K.
• Added support for DL 18mm F2.8 ASPH Lens.
• Added support for recording 1-120fps S&Q (Slow motion and Quick motion) for Zenmuse X9-6K and Zenmuse X9-8K gimbal cameras.
• Added support for displaying three channels of exposure waveform for the high-bright main monitor.
• Added support for multi function dial settings of the main body.
• Added support for recording full frame video at 17:9 ratio when sensor frame is set at 50fps for Zenmuse X9-6K gimbal camera (6K resolution is 5952*3136).
• Added loop code for folder and file names to avoid repeated names.
• Added percentage adjustment for focus peaking.
• Added auto recognition and calibration file loading for electronic lenses.
• Added support for remaining in broadcast mode after restarting Ronin 4D.
• Added support for enlarging the safety zone and frame guide along with the Focus Mag.
• Added support for auto detection and repair for damaged footage when inserting a storage device. Only supports footage recorded with Ronin 4D or Inspire 3. The repaired audio and video duration depends on the degree of damage to the footage and cannot be guaranteed that all of the footage can be repaired.
• Optimized the playback fluency issue when playing the high-quality videos.
• Fixed issue: Focus motors need to be initialized after restarting.
• Changed the recording time format to xx h xx m.
Notes:
• Update the firmware to the latest version for accessories (except for DJI RS Focus Motor (2022)) before mounting on the Ronin 4D Flex. Update the firmware of DJI RS Focus Motor (2022) in DJI Assistant 2 after connecting to the Ronin 4D Flex using the CAN port.
• Make sure to update both the Video Transmitter and High-Bright Remote Monitor to the latest firmware version. Otherwise, the video transmission may work abnormally.
• If the update fails, restart the device and try again.
• Added support for Zenmuse X9-8K gimbal camera, which supports 4K resolution and up to 120fps full frame video recording. Due to performance limitations, clean footage is not supported in ProRes RAW format and 48 project frame rate or above video and only supports the OSD output when using the HDMI port of the main body and SDI port of the expansion plate with Zenmuse X9-8K.
• Added support for DL 18mm F2.8 ASPH Lens.
• Added support for recording 1-120fps S&Q (Slow motion and Quick motion) for Zenmuse X9-6K and Zenmuse X9-8K gimbal cameras.
• Added support for displaying three channels of exposure waveform for the high-bright main monitor.
• Added support for multi function dial settings of the main body.
• Added support for recording full frame video at 17:9 ratio when sensor frame is set at 50fps for Zenmuse X9-6K gimbal camera (6K resolution is 5952*3136).
• Added loop code for folder and file names to avoid repeated names.
• Added percentage adjustment for focus peaking.
• Added auto recognition and calibration file loading for electronic lenses.
• Added support for remaining in broadcast mode after restarting Ronin 4D.
• Added support for enlarging the safety zone and frame guide along with the Focus Mag.
• Added support for auto detection and repair for damaged footage when inserting a storage device. Only supports footage recorded with Ronin 4D or Inspire 3. The repaired audio and video duration depends on the degree of damage to the footage and cannot be guaranteed that all of the footage can be repaired.
• Optimized the playback fluency issue when playing the high-quality videos.
• Fixed issue: Focus motors need to be initialized after restarting.
• Changed the recording time format to xx h xx m.
Notes:
• Update the firmware to the latest version for accessories (except for DJI RS Focus Motor (2022)) before mounting on the Ronin 4D Flex. Update the firmware of DJI RS Focus Motor (2022) in DJI Assistant 2 after connecting to the Ronin 4D Flex using the CAN port.
• Make sure to update both the Video Transmitter and High-Bright Remote Monitor to the latest firmware version. Otherwise, the video transmission may work abnormally.
• If the update fails, restart the device and try again.