DDD release notesDankDroneDownloader catalog
What’s New?
• Initial Release
• Added Auto to Focus mode. If Auto is enabled, focus will automatically turn on or off based on the scene.
• Added 200mw and 500mw when selecting the max power limit for the video transmission. Make sure to follow local regulations when setting the max power limit.
• Added framing lines. If a DJI Osmo Action is attached to the aircraft, the size and positon of the framing lines can be adjusted to make sure that camera view can be displayed on the goggles.
• Added support for saving on-screen display information as subtitle files when recording by the goggles.
• Added screensaver for goggles.
• Changed DJI HDL to Sbus Baud Fast under Protocol in Device Info in Setting.
• Optimized multilingual text.
• Optimized display of AV IN analog video transmission.
• Added ability to adjust screen position and size.
• Added microSD card error prompt. "SD SLOW" appears when recording stops due to slow writing speed.
• Fixed issue: microSD card could still be formatted while recording.
• Fixed occasional issue: only the air unit would record even when both the air unit and goggles were set to record simultaneously.
• Fixed rare issue: UI interface froze during playback.
• Fixed issue: writing issue during recording caused the screen to blur or freeze.
• Fixed issue: to ensure safety during tuning and debugging, the air unit sent an enable or disable arming prevention command when entering or exiting the RC setting on the goggles or when plugging or unplugging the USB-C port of the air unit. The Betaflight Configurator also had a similar protection feature as the DJI FPV Air Unit. When both the Betaflight Configurator and the DJI FPV Air Unit were connected to the flight controller and were being operated simultaneously, the arming prevention may be accidentally disabled. In order to prevent such accidents, the DJI FPV Air Unit no longer sends disable arming prevention commands. Betaflight will evaluate whether to add to client ID to future flight controller firmware to improve security.
Notice:
• Restart the air unit, goggles, and remote controller once the update is complete.
• Make sure that the firmware of the air unit, the goggles and the remote controller are in the same version. Check the firmware version in Setting, then Device Info, and then Device Info on goggles.
• If the firmware update fails, restart the device and DJI Assistant 2 (DJI FPV Series), and try updating again.
• Restart the air unit after setting the protocol between the air unit and flight controller.
Coming in Next Update:
• Optimize the flight controller on-screen display information and add ability to customize the display.
• Support for recording AV IN analog video transmission.
• Initial Release
• Added Auto to Focus mode. If Auto is enabled, focus will automatically turn on or off based on the scene.
• Added 200mw and 500mw when selecting the max power limit for the video transmission. Make sure to follow local regulations when setting the max power limit.
• Added framing lines. If a DJI Osmo Action is attached to the aircraft, the size and positon of the framing lines can be adjusted to make sure that camera view can be displayed on the goggles.
• Added support for saving on-screen display information as subtitle files when recording by the goggles.
• Added screensaver for goggles.
• Changed DJI HDL to Sbus Baud Fast under Protocol in Device Info in Setting.
• Optimized multilingual text.
• Optimized display of AV IN analog video transmission.
• Added ability to adjust screen position and size.
• Added microSD card error prompt. "SD SLOW" appears when recording stops due to slow writing speed.
• Fixed issue: microSD card could still be formatted while recording.
• Fixed occasional issue: only the air unit would record even when both the air unit and goggles were set to record simultaneously.
• Fixed rare issue: UI interface froze during playback.
• Fixed issue: writing issue during recording caused the screen to blur or freeze.
• Fixed issue: to ensure safety during tuning and debugging, the air unit sent an enable or disable arming prevention command when entering or exiting the RC setting on the goggles or when plugging or unplugging the USB-C port of the air unit. The Betaflight Configurator also had a similar protection feature as the DJI FPV Air Unit. When both the Betaflight Configurator and the DJI FPV Air Unit were connected to the flight controller and were being operated simultaneously, the arming prevention may be accidentally disabled. In order to prevent such accidents, the DJI FPV Air Unit no longer sends disable arming prevention commands. Betaflight will evaluate whether to add to client ID to future flight controller firmware to improve security.
Notice:
• Restart the air unit, goggles, and remote controller once the update is complete.
• Make sure that the firmware of the air unit, the goggles and the remote controller are in the same version. Check the firmware version in Setting, then Device Info, and then Device Info on goggles.
• If the firmware update fails, restart the device and DJI Assistant 2 (DJI FPV Series), and try updating again.
• Restart the air unit after setting the protocol between the air unit and flight controller.
Coming in Next Update:
• Optimize the flight controller on-screen display information and add ability to customize the display.
• Support for recording AV IN analog video transmission.